英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

LUP    

请选择你想看的字典辞典：
单词字典翻译
lup查看　lup　在百度字典中的解释百度英翻中〔查看〕
lup查看　lup　在Google字典中的解释Google英翻中〔查看〕
lup查看　lup　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • What does strap mean in this context? - Electrical Engineering Stack . . .
    The violation you have, LUP 6 (atch- rule 6) indicates that there is no such strap near the offending transistor While 30 um is the maximum distance, it is encouraged to place a strap, or perhaps an entire guard ring, as close as possible to the transistor
  • debounce - Suitable RC debouncing circuit? - Electrical Engineering . . .
    What is the button used for? Where is it connected to? It kind of determines what kind of debouncing, if any, is needed Also, what might be important, is what kind of button is it If it has a datasheet, you can read the maximum it can safely handle, and minimum current needed to keep contacts clean, and that may help in determining resistance values, and that combined with the debouncing
  • Zener Diode Reverse Current - Electrical Engineering Stack Exchange
    I have this - Zener Diode - 12V Reverse Voltage On the table 8, I can see the ranges for the 12V reverse voltage is between 11 4V and 12 7V for the quot;C quot; selection part But this value if f
  • What does IDC stand for in inductor for boost converter?
    In Webench at TI com it states "IDC" as a parameter for the inductors What does this stand for? Saturation current? max current? ripple current? something else?
  • capacitor - Electrical Engineering Stack Exchange
    Why is the time constant (RC) measured in seconds even though the units are farads x ohms? This is to fulfill my own curiosity as I haven't had much luck at finding the answer I would be most gra
  • Capacitor selection on Kicad - Electrical Engineering Stack Exchange
    Can someone assist me in finding the correct footprint for this capacitor? The footprints on Kicad are: What does CP_elec_3x5 3 relate to? What does 3 x 5 3 mean? And the capsize is here:
  • What happens if two N-wells touch each other?
    The DRC rule you are referring to is the separation of two wells at different potentials DRC has no way of knowing what is the potential of the well (no connectivity information at this level), so if you have two separate NWELLS it will enforce this rule If you have two NWELLS at the same potential then you have two choices: Directly abut them, so that these become a single NWELL Separate
  • 5 Band resistors and correct orientation
    few days ago i bought few (about 500) resistors and i noticed that they have 5 color bands instead of 4 My question is how do i count them (which color is the tollerence) and how should i put them
  • IPC-B-25A test board schematic - Electrical Engineering Stack Exchange
    I need to design an IPC-B-25A IPC multipurpose test board I have only following board image Board features are below: Solder mask - None FR4 Tg=175°C Size - 4 quot;x4 5 quot; (10x11 4cm) Thickne
  • safety - Difference between interlock and permissive - Electrical . . .
    My thinking : Permissive : A condition within a logic sequence that must be satisfied before the sequence is allowed to proceed Interlock : A device used to prove the physical state of a required condition and to furnish that proof to the primary safety control circuit Hence , the "Permissive" is a condition which can be checked by the "Interlock" to proceed Example 1 : "Starting the





中文字典-英文字典  2005-2009